Close Menu
    Cryptocurrency

    My Own Liquid Mining Bitcoin Farm! DCX Immersion Installation and Review



    Today I am setting up my own Bitcoin immersion mining farm, this is liquid cooled BTC mining, which allows for higher Bitcoin mining profitability, and spending less electricity mining earning more passive income! How easy is the DCX enclosure and dry cooler install? I’ll show you lol! Start mining yourself today here – https://voskco.in/tailsxch

    Learn more about DCX immersion mining options – https://voskco.in/dcx
    VoskCoin Mining Farm Tour video playlist – https://youtube.com/playlist?list=PL4dnwHTjcf-8SXMDAoL7-XFkV6b4XUH3j&si=BD6oDOgXluoXOvnM
    Buy your own Bitcoin miners here – https://voskco.in/am
    Altair Tech PDUs and BTC ASIC parts – https://voskco.in/altair
    Evergreen plug and play low power miners! https://voskco.in/evg
    Use code VOSKCOIN to save some COIN!

    I have toured some crazy Bitcoin immersion mining farms over the years and thanks to DCX I am finally going to start immersion mining Bitcoin myself! DCX has a plug and play immersion mining setup, they have options for single phase electricity and three phase electricity, in this video I am installing DCX immersion mining kit in my single-phase bitcoin mining farm. I also use Braiins s19 firmware which supports immersion mining because I did not have fan spoofers which are needed to when Bitcoin ASIC mining rigs are running in a liquid without fans. While this isn’t a step by step installation guide, hopefully this helps anyone feel more comfortable doing a DCX immersion mining farm build. If you have questions just leave a comment and I’ll try and check back and help with what I learned setting up my own liquid cooled immersion bitcoin mining deployment!

    Contact BMA Enterprises crypto division here – https://voskco.in/bma

    ⏰ Timestamps ⏰
    00:00 Setting up the immersion bitcoin mining shed
    00:40 Immersion mining is crazy Quiet!
    02:25 Make sure your miners are clean before you immerse them!
    03:27 Installing a different firmware on the Bitmain s19
    05:37 Installing the DCX dry cooler
    07:49 Manually Pumping the coolant
    09:31 Using shrouds on the Bitcoin miners
    11:00 Pouring the immersion fluid into the DCX immersion tank!
    12:46 Turning on and opening al the valves
    14:06 Powering the Immersion setup
    15:22 Using the Altair pdu
    17:14 Fixing bad miners
    18:00 How is my wire management?
    19:50 Installing the new Altair PDU’s
    22:37 Should you immersion mine at home?
    25:25 Using a transformer for electricity
    26:11 Get connected with the community!
    27:00 Thanks to BMA for helping!
    28:06 Immersion mining is nice and quiet!
    29:40 Make it happen!

    Follow us on our official social media accounts – https://voskco.in/23

    VoskCoin is for entertainment purposes only and is never intended to be financial investment advice. VoskCoin owns or has owned cryptocurrency and associated hardware. VoskCoin may receive donations or sponsorships in association with certain content creation. VoskCoin may receive compensation when affiliate/referral links are used. VoskCoin is home of the Doge Dad, VoskCoin is not your Dad, and thus VoskCoin is never liable for any decisions you make.

    #Bitcoin #BTC #PassiveIncome #VoskCoin #immersion #dcx #bitmain #antminer #bitcoins #mining #miningfarm #workfromhome #miner #mine

    View 27 Comments

    27 Comments

    1. Colby_Attack on

      The install was buttery except getting covered in antifreeze!

      The lesson learned was that those hose clamps should probably only be used once and then discarded. I think the bolt stretches enough to weaken it – the whole system is about 30PSI/2Bar.

    6. troy lindsey on

      I use my hot fluid to heat my shop and wife’s sewing shop. Just add bypass loop and run the hot fluid through a heater coil. Just curious what’s your average fluid temp? And how much TH are you getting?

    7. troy lindsey on

      Ohh forgot to tell you a heated my hoses up with a heat gun then pushed them on. I also used a bucket of super hot water to expand the hose a little before sliding them on but heat gun is best!!

    13. Leidys Sanchez on

      Great video, trading come with a lot of benefits And I have just bought my first house through it. As a beginner I was scared of Loosing my savings but I'm glad I took the bold step that is now favoring me.

    15. Fast Lane on

      Hey dude- found a property in TN with a natural gas well on it. Any advice on who I can tall to to see if the well produces enough gas to run at least 10 S19jPros?

    18. Kyle F on

      6:16 not to code, should have drilled next to the stud, sleeved with pvc, strap said pcv to stud and then pass connections and silicone afterwards

    19. Riceman on

      Cool, destroying the planet performing silly tasks. This has to be one of the dumbest ideas that human beings have come up with in decades.

    23. jabuki on

      Every time I see immersion systems I always want to know about filtration. It's nice and clean now and there is a cover, but every spec of dust that hits that fluid stays in that fluid and after a couple years your exchange cooler is going to be holding all that dust inside it and it will be impossible to remove. I would have liked to see a filtration unit for the fluid going to the cooler.

    Leave A Reply
    Share via